Airaid 883-282 Manuale Utente Scaricare il pdf

Installation Instructions

For Part Number:

883-282 Intake kit with scoop

2008-14 Polaris Ranger RZR 800

1. Many of the panels needing to be removed for this

installation are held in place with the use of nylon riv-

ets. Nylon rivets are reusable if care is taken during

their removal and installation. Using a small standard

blade screwdriver, gently pry up on the center post until

the entire rivet can be pulled freely from the panel. Riv-

et installation is the opposite.

2 Place the range selector in Park. And remove both driv-

er and passenger seats. Disconnect the negative terminal

on the battery.

3. Remove the front engine cover by rotating the two

twist locks counter clockwise and lifting out.

4. Remove the bed bolts

A.) Using a 1/2” socket, remove the four inner bed

bolts.

B.) Using a T-25 Torx driver, remove the four outer

bed bolts.

5. Using a T-25 Torx driver and a 7/16” wrench, remove

the two outer bed bolts.

7. The bed is fastened from underneath by four Phillips

head screws in these locations. Remove these screws

on both the driver and passenger sides of the vehicle.

6. Using a T-25 Torx driver, remove the four outer bed

bolts.

8. Under side view of three bed screws to remove.

Advisory Note:

Please read these installation instruc-

tions in their entirety before begin-

ning the install process. Airaid strong-

ly recommends the use of Locktite®

242 Medium strength threadlocker on

all threaded fasteners.

B. B.

Tools Required For Installation:

7/16” and 1/2” Wrenches. 10mm, 7/16”, and

1/2” Sockets.

T-25 Torx driver. Ratchet & Extension. 1/8”&

5/16” Drill bits. 3” hole saw and drill. Center

punch and Mallet

Phillips and Standard Tip Screwdrivers.

Locktite ® 242 or equivalent, and a roll of tape

Full color instructions can be viewed on our web site at Airaid.com. Use the Product Search function to find your part number, and click View Details.

Page 1

1 2 3 4 5 6 7

Sommario

Pagina 1 - Installation Instructions

Installation Instructions For Part Number: 883-282 Intake kit with scoop 2008-14 Polaris Ranger RZR 800 1. Many of the panels needing to be

Pagina 2

12. Remove the two rivets holding the intake shroud to the frame. Then remove the shroud and set it aside. 13. Remove the last three ri

Pagina 3 - Trans Mount Washer

24. Place the Air Box Gasket (#22) onto the face of the Air Box and align the bolt holes. 26. Place the Air Box assembly into the vehicle with t

Pagina 4 - Filter Service

36. Slide the Riser Tube Gasket (#23) on to the Thread-ed Studs. 37. Slide the Riser Tube with Studs and gasket through the panel as shown. 38. Moun

Pagina 5 - Tune-Up Kit!

Pre Filter Option For maximum protection in the harshest of environments. Airaid of-fers a slip on Pre Filter for the 700-411 Air filt

Pagina 6 - Component Identification

Component Identification Page 6 1. Airaid Premium Filter 1 2. Cold Air Box 1 3. Air Box Top 1 4. Riser Tube 1 5. Air Inlet Scoop 1

Pagina 7 - ATTENTION !

6.0001.0003.00IN. HOLE SAW5/16 DRILLUSE SPRING LOADED CENTER PUNCH TO MARK HOLESSTART WITH 1/8 DRILLFOR PILOT HOLESALIGN EDGES AGAINSTRADIUS OF FENDER

Modelli collegati 883-283

Commenti su questo manuale

Nessun commento

Airaid 883-282 Manuale Utente

Navigare online o scaricare Manuale Utente per Apparecchiature per l'aria compressa Airaid 883-282. Airaid 883-282 User Manual Manuale Utente

Sommario

Modelli collegati 883-283

Commenti su questo manuale

Prodotti e manuali riguardandi Apparecchiature per l'aria compressa Airaid 883-282